The following information about Arizona Oversize Permits is for informational purposes only. It’s important to always read your permits and provisions sheets carefully as we cannot guarantee the accuracy of the information provided. If you have any questions or need assistance, you can contact the following number.

 Arizona DOT # 602-771-2960

Arizona Oversize Permits Duration

Arizona oversize permits are valid for four days and can be obtained at most Ports of Entry.

Operating Time

Daylight hours (half-hour before sunrise to half-hour after sunset) apply. For loads/vehicles not exceeding 10′ wide, 14’6″ high, or with a rear overhang of 10′, continuous travel is allowed. Loads not exceeding 16′ wide, 16′ high, 120′ long, and 250,000 pounds may travel at night on Interstate and specified state routes from 3:00 am to 12:00 noon on weekends (excluding holiday weekends and curfew areas). This must be specified during permit ordering. Note: Loads over 11′ wide require one escort during weekend travel from 3 a.m. to noon, and loads 15′ high and above need an escort with a height pole.

Restricted Travel in Arizona

No oversize or overweight loads are permitted on I-17, I-10, and SR 60 within the city limits of greater Phoenix area, or on I-10 or I-19 within the city limits of greater Tucson area between 7:00 am – 9:00 am and 4:00 pm – 6:00 pm on weekdays. Local “Courtesy Permit”/route approval is mandatory for oversize load travel within Phoenix and Tucson.

Call (832) 454-5883 For Permit Consultation

Legal Dimensions for Arizona Oversize Permits

Length:

  • 57′ trailer on Interstate
  • Non-designated roads, 65′ overall for over 53′ semi-trailer

Overhang:

3′ front, 6′ rear.

Width:

8′-6″

Height:

14′

Weight:

80,000 Gross

  • Single – 20,000
  • Tandem – 34,000
  • Tridem – 42,000

Routine Permit Limits in Arizona

Length:

120′

Width:

14′

Height:

16′

Weight:

  • Tandem – 46,000*
  • Tridem – 51,450–53,974
  • Single – 28,000
  • *(Tandem and Tridem weights may vary depending on axle spacing, and axle width. For example, a tridem with 9′ of axle spacing (4′-6″ + 4′-6″) and 8′ axle width gets 51,450).

Note: A “Class C Tridem Permit” permits a weight of 59,168 pounds with a Tridem axle spacing of 9′ (57,960 pounds at 8′, 60,000 pounds at 10′). This allowance is applicable exclusively for travel on Interstates 10, 19, and 40, as well as the sections of SR68 and US93 connecting I-40 

and the Nevada line. Traveling on any other routes, including detours, will result in disqualification.

Over 14′ wide, 16′ high, 120′ long and 250,000 requires a “Class C”.  A route survey may be required.

Arizona Oversize Permits image

Escort Requirements for Arizona Oversize Load Permits

Length:

  • over 120′ – one or more escorts.

Overhang:

Front or Rear over 20′ – one escort.

Width:

  • over 14’– 1 or more escorts.
  • Some restricted routes require two escorts over 12′ wide and a few for over 10′ wide.

Height:

over 16′ – one or more escorts.

Miscellaneous

Bulldozer blades and arms exceeding 14′ in width, measured at right angles to the trailer axis, must be detached and transported to ensure safety. Dozer blades narrower than 14′ may be transported without detachment if the dozer is securely supported. Easily removable components such as buckets, blades, and counterweights should be removed; however, they can be transported with the load. Blades can be detached and transported on the same trailer if the load would be overweight with or without the blade, but this must be specified in the permit. Wide loads require side mirrors extending sufficiently to maintain visibility.

Signs, Flags & Lights for Arizona Oversize Load Permits

All vehicles or loads wider than 9′ must display “Oversize Load” signs. Overwidth loads and vehicles must be flagged with red flags (12″ square or larger) on extremities. Front or rear overhangs must be flagged or illuminated. Up to 10′ overhang is permitted at night but must be lit and flagged. Overheight or overweight-only loads do not require signs or flags.

Note on Arizona Oversize Permits: Arizona scales expect permit weights to closely match actual weights and dimensions. Permits can be obtained at the scales to ensure accuracy, preventing potential issues.